PSC LINEAR IMAGER 7000 Wartungshandbuch

PowerScan® 7000BT SRILinear ImagerQuick Reference Guide

2 PowerScan® 7000BT SRIOrient the Battery Pack as shown in Figure 1, then push it into the scan-ner until the alignment pins engage and the unit snaps

Getting StartedQuick Reference Guide 3Figure 1. Battery Pack Installation & RemovalVerifying Scanner Operation Before Linking to the Base StationO

4 PowerScan® 7000BT SRIConnectionFigure 2 shows how to connect the Base Station to a terminal, PC or other host device. Turn off the host before conne

Getting StartedQuick Reference Guide 5Host Connection — The interface type was specified at the time your scanner was ordered, however you should veri

6 PowerScan® 7000BT SRIascending tones from the scanner. A “high-low-high-low” tone indicates the link attempt was unsuccessful. A single LED flash du

Getting StartedQuick Reference Guide 7Linking the Scanner to a Bluetooth DeviceA scanner can optionally be linked to a PC with a Bluetooth radio insta

8 PowerScan® 7000BT SRIThere presently are no US, North America or World disposal require-ments for Lithium-Ion batteries such as the Battery Pack, so

Getting StartedQuick Reference Guide 9Interface SelectionSelect the desired interface by scanning the associated bar code below. For Keyboard Wedge in

10 PowerScan® 7000BT SRITable 1-1. Keyboard Wedge Interface ReferenceIBM USBUSB HIDKeyboardUSB HID POSI/F Type PCs SupportedA PC/XT w/Alternate Key En

Getting StartedQuick Reference Guide 11QIBM 3153IBM 316X, 3179/3180/319X/3270R IBM 3151/3152-010, 347X/348XS DIGITAL VT 220/320/330/340/350/382T DIGIT

Datalogic Scanning, Inc.959 Terry StreetEugene, Oregon 97402Telephone: (541) 683-5700Fax: (541) 345-7140An Unpublished Work - All rights reserved. No

12 PowerScan® 7000BT SRIKeyboardWedge HKeyboardWedge IKeyboardWedge JKeyboardWedge K KeyboardWedge LKeyboardWedge MKeyboardWedge NKeyboardWedge OKeybo

Getting StartedQuick Reference Guide 13Resetting the Standard Product DefaultsIf programming settings for your scanner are in an unknown condition, fa

14 PowerScan® 7000BT SRIHow to ScanWhen the trigger is pressed, the scanner projects a red, horizontal illumi-nating beam. This beam will remain on un

TroubleshootingQuick Reference Guide 15Figure 6. Scanning Bar CodesTroubleshootingTroubleshoot your scanning system by performing the following checks

16 PowerScan® 7000BT SRI• the scanner is linked to the desired Base Station. See "Linking the Scanner to a Base Station" on page 5.• the sca

TroubleshootingQuick Reference Guide 17• are enabled in the scanner. See the Product Reference Guide (PRG) for more about configuring the scanner to r

18 PowerScan® 7000BT SRI• The scanner sounds other than a standard “Good Read” beep fol-lowed by an “Acknowledge1” beep when reading a bar code (indi-

DECLARATION OF CONFORMITYDatalogic hereby declares that the Equipment specified below has been tested and found compliant to the following Directives

©2007 Datalogic Scanning, Inc. R44-2708 (Rev. B) 5/07AustraliaDatalogic Scanning Pty LtdNorth Ryde, AustraliaTelephone: [61] (2) 9870 3200Fax: [61] (

Quick Reference Guide iStatement of Agency ComplianceThis device complies with part 15 of the FCC Rules. Operation is subject to the following two con

ii PowerScan® 7000BT SRISolids and Water ProtectionThe Imager is rated as IEC 529-IP65. This nomenclature designates the degree of water and dust resi

Quick Reference Guide iii4. Intellectual Property.End User acknowledges that the Software constitutes valuable trade secrets of Datalogic or Datalogic

iv PowerScan® 7000BT SRIputer software developed at private expense as set forth in the U.S. Federal Acquisition Regulations at FAR52.227-14(g), or 52

Quick Reference Guide vTable of ContentsStatement of Agency Compliance ... iFCC Class B Compl

vi PowerScan® 7000BT SRINOTES

Quick Reference Guide 1Getting StartedInstalling the Battery PackNOTETo charge the Battery Pack, See “Battery PackCharging and Maintenance” on page 7.